SANITIZING WATERBASED LACQUER FOR FURNITURE
IGNAT4122.1-XX
Eco-compatible finish for the treatment and active cleaning of furniture.
It respects the environment, workers health and protects user's health thanks to its water base, almost non-existent VOC content and iG PURE innovative technology.
Mobilack develops very high levels of protection against wear, abrasion and bacteria thanks to the controlled release of Silver ions.
High performance with the ease of use of a single component and self-regenerating protection.
By need or aim, Mobilack can be further improved in performances by adding its specific hardener,(two component).Hardener addition ratio is 10%.
Available in gloss levels: natural effect 5% - deep matt 10% - matt 30% - semiglossy 60% - glossy 90%.
Recommendations for application:
The product can be applied by Brush, Spray or Roller directly on sanded raw wood or on water-based or oil-based basecoats.
It can be applied on Borma Oil finishes as well, prior a proper sanding.
Approx yield: 10-14 m2/Lt.
Sanitizing waterbased Furniture lacquer
Sheen (Gloss):
- 0/5 absolute opaque
- 10/20 deep matte
- 30/40 opaque
- 50/60 semilucid
- 80/90 full glossy
Conformity EN 71.3 Toy safety - Part 3: Migration of certain items
Cod. IGNAT4122.1-XX - 6 x 1LT
Cod. IGNAT4122.5-XX - 2 x 5LT
Cod. IGNAT4122.10-XX - 10LT
Cod. IGNAT4122.20-XX - 20LT
LOGIN
Apply on a smooth and clean surface, free from oils, greases, waxes, silicones and old varnishes, properly sanded.
If used as bicomponent mix varnish and CATALYST 4100-2K in ratio 10 : 1, stir very well then add 5-10% of water (possibly demineralized), and stir again. Wait 10 minutes.
Apply Mobilack in two or three coats (80-100 mL/m² each), depending on the final desired touch of the finish.
After each coat wait and sand with abrasive paper grit 220, aspirate with care all the dust and clean with an antistatic cloth. Then apply the next coat of Mobilack.
Drying time between the 2 coats: 2/4 hours
Related products
LEGENDA
Conformity EN 71.3 Toy safety - Part 3: Migration of certain items.
Eurofins danish laboratories have recognized the conformity of Borma Wachs oils to EN 71-III norm, relating to the migration of harmful heavy metals, guaranteeing the safety of the treatments in such a way that they can also be safe for use on childrens' toys.
Labeling of construction products
This label covers the French legislation relating to emissions of volatile organic compounds (VOC) and the impact they have on indoor air quality after the product is brought into the room.
Labeling refers to the pollutants emitted once the products are spread and dried.
The IBR Green Building Institute had tested some of our products and determined that they correspond to the highest standards of the aforementioned French VOC legislation.
EMICODE EC1 - Low-emission building materials
Certified installation materials, adhesives and construction products
The EMICODE mark guarantees that the material has been tested and certified according to its emission level. Compared to 1997, low-emission building materials now have a TVOC value (total quantity of volatile organic compounds) from one hundred to one thousand times lower. The EMICODE mark is not issued if a building material is suspected of altering genetic makeup, causing cancer or impairing reproductive capacity.
APEO (alkylphenol ethoxylates)
APEOs (alkylphenol ethoxylates) are highly persistent chemicals, which are deposited in the tissues, penetrating, through them, into the food chain.
Recent studies demonstrate its toxicity and danger, as potential endocrine disruptors.